My Light Diagram

 12V to +-20V Automotive Power Converter Diagram The limitation of car supply voltage (12V) forces to convert the voltages to higher in order to power audio amplifiers. In fact the max audio power x speaker (with 4 ohm impedance) using 12V is (Vsupply+ - Vsupply-)^2/(8*impedance) 12^2/32 = 4.5Watts per channel, that is laughable... For powering correctly an amplifier the best is to use a symmetric supply with a high voltage differential. for example +20 - -20 = 40Volts in fact 40^2/32 = 50 Watts per channel that is respectable. This supply is intended for two channels with 50W max each (of course it depends on the amplifier used). Though it can be easily scaled up or the voltages changed to obtain different values.

This circuit is designed to generate a 20KHz pseudo sine wave signal that can power about 50 remote touch activated switch circuits.  It can support a cable length of about 2500 feet.  A typical remote switch circuit is also shown as well as a receiver circuit for those switches. 12V Touch Switch Exciter Circuit diagram:  Source: discovercircuits

Drive a standard 36/40W fluoro tube to fll brightness from a 12V DC. Ideal for camping, a trouble light or even emergency home lighting. For these reasons, fluorescent lighting is the natural choice in commercial and retail buildings, workshops and factories. For battery-powered lighting, fluorescent lights are also the first choice because of their high efficiency. The main drawback with running fluorescent lights from battery power is that an inverter is required to drive the tubes. Inverter efficiency then becomes the major issue. There are many commercial 12V-operated fluorescent lamps available which use 15W and 20W tubes. However, it is rare to see one which drives them to full brilliance. For example, a typical commercial dual 20W fluorescent lamp operating from 12V draws 980mA or 11.8W. Ignoring losses in the fluorescent tube driver itself, it means that each tube is only supplied with 5.9W of power which is considerably less than their 20W rating. So while the lamps do use 20W...

Car 12V to 50V DC Converter Circuit Diagram This circuit for Car audio input battery 12V to 50VDC, It use transistor and IC TL072.

This is the Simple 12V Portable and Mobile Power Supply Schematic .This type of power supply can be built quite inexpensively and needs only a minimum of circuitry. This circuit will give output current of 1 amp, well stabilized and smoothed. Simple 12V Portable and Mobile Power Supply Schematic The smoothing and regulation is provided by IC1 7812 which is a 12V monolithic voltage regulator. Thisportable power supplyunit incorporates output current limiting and is therefore not damaged by accidental short term short circuits or other forms of output overloading.   components Resistor1/3 watt 5% R1 1.8k Capacitors Cl 2200uF 25V electrolytic C2 100nF polyester (C280) C3 100nF polyester (C280) Semiconductors ICI uA78I2 (12 volt 1 amp positive regulator) D1 to D4 1N4002(4 off) Switch S1 DPST toggle type Transformer T1 Standard mains primary, 15 — 0 — 15 volt 2 amp secondary

This circuit provides a 12V regu-lated power supply with output current up to 3 amperes. It is spe-cially designed for use with 2m handheld rigs with linear power amplifier and CB portable QRP rigs. The circuit uses monolithic IC CA3085 voltage regulator in 8-lead TO-5 package.  Its salient features include good load and line regulation, output current up to 100 mA (which can be increased to several amperes with additional pass transistors), output short-circuit protection, and lower input voltage.  A low power dissipation is achieved by driving external series-pass transistor 2N4241 (T1) from  pin 2 of CA3085. Circuit diagram :   12V, 3A Power Supply Circuit Diagram Normal output pin 8 is returned to ground via diodes D3 and D4 to ensure error am-plification operation in the linear region. Ripple rejection is approximately 50 dB on no load and 35 dB on full load.  A 2x2x2.5cm aluminium heat sink fas-tened onto a 1.5mm blackened aluminium sheet of 12.5cm2 are...

Build a simple 500W Cheap 12V to 220V inverter Circuit Diagram.  In this circuit 4047 is use to generate the square wave of 50hz and amplify the current and then amplify the voltage by using the step transformer. 500W Cheap 12V to 220V inverter Circuit Diagram How to calculate transformer rating The basic formula is P=VI and between input output of the transformer we have Power input = Power output For example if we want a 220W output at 220V then we need 1A at the output. Then at the input we must have at least 18.3V at 12V because: 12V*18.3 = 220v*1 So you have to wind the step up transformer 12v to 220v but input winding must be capable to bear 20A.   Source: www.circuitsproject.com

Using LT3582-12 dual channel DC DC converter integrated circuit, manufactured by Linear Technology, can be designed a very simple step up dc converter. This 5 to 12V c converter electronic project provide both positive and negative outputs required in many biasing applications such as active matrix OLED (organic light-emitting diode)displays as well as CCD (charge coupled device) applications. Simple LT3582-12 DC 5V to 12V DC Converter  Circuit Diagram

To get a more precise output voltage, replace zener diode Z1 with 10V and R1 with a 1Kilo ohm potentiometer. A Coolrib for Q1 is optional but highly recommended. You can replace Q1 for a more robust type to get more output amps depending on your requirements. Simple circuit to power your 9 volt cassette recorder and other stuff. Parts List: R1 = 560 ohm C1 = 1000uF/40V, Electrolytic C2 = 10uF/25V, Electrolytic C3 = 330nF, Ceramic Z1 = 9.1V, 1watt zener Q1 = ECG184, NTE184 

Attention: This Circuit is using high voltage that is lethal. Please take appropriate precautions Using this circuit you can convert the 12V dc in to the 220V Ac. In this circuit 4047 is use to generate the square wave of 50hz and amplify the current and then amplify the voltage by using the step transformer. How to calculate transformer rating The basic formula is P=VI and between input output of the transformer we have Power input = Power output For example if we want a 220W output at 220V then we need 1A at the output. Then at the input we must have at least 18.3V at 12V because: 12V*18.3 = 220v*1 So you have to wind the step up transformer 12v to 220v but input winding must be capable to bear 20A. Author:Ashad Mustufa website: http://www.electronics-lab.com

This is the 1.5V to 5V/12V DC/DC Converter with LT1073 Project. Small 1.5V to 5V or 12V DC/DC converter with LT1073 chip. The IC is available in three different versions, depending on output voltage. Two with fixed output voltage of 5V and 12V, and the most interesting that can be adjusted. The adjustment is done through a voltage divider with two resistors, of mass, output and Terminal 8, internally connected to the voltage comparator IC, which is responsible for stabilizing the output voltage. LT1073 has an internal everything you need to make a small DC / DC converter with a low operating voltage of only 95μA 1V and consumption without load. If you do not have a meter inductance, the inductive part of the drive is a bit more complicated to make, but we shall see some possible solutions. Capacitor also recommended by the manufacturer for the circuit is a bit hard to get, I have used a tantalum recovered from another power source, and the ripple voltage at the output is quite low....

Using ADP2300 ADP2301 step-down dc dc regulators with integrated power MOSFET, can be designed a very simple DC DC voltage converter. Output voltage delivered by these circuits can be adjusted from 0.8 volts, up to 0.85xVin , with ±2% accuracy. The maximum output current that can be provided by ADP2300 ADP2301 regulators is up to 1.2 A load current. 12V Step-Down Dc Converter Circuit Diagram   There are two frequency options: the ADP2300 runs at 700 kHz, and the ADP2301 runs at 1.4 MHz. These options allow users to make decisions based on the trade-off between efficiency and total solution size. Current-mode control provides fast and stable line and load transient performance.  Bellow you an see two design examples, which require few common electronic components.First circuit will provide a 2.5V output at a maximum current of 1.2A from an input voltage of 12 volts. Second circuit will provide a 5V output at a maximum current of 1.2A from an input voltage of 12 volts.

Using ADP2300 ADP2301 step-down dc dc regulators with integrated power MOSFET, can be designed a very simple DC DC voltage converter. Output voltage delivered by these circuits can be adjusted from 0.8 volts, up to 0.85xVin , with ±2% accuracy. The maximum output current that can be provided by ADP2300 ADP2301 regulators is up to 1.2 A load current. 12V Step-Down Dc Converter Circuit Diagram There are two frequency options: the ADP2300 runs at 700 kHz, and the ADP2301 runs at 1.4 MHz. These options allow users to make decisions based on the trade-off between efficiency and total solution size. Current-mode control provides fast and stable line and load transient performance.  Bellow you an see two design examples, which require few common electronic components.First circuit will provide a 2.5V output at a maximum current of 1.2A from an input voltage of 12 volts. Second circuit will provide a 5V output at a maximum current of 1.2A from an input voltage of 12 volts.

The usual chargers of battery automotive, are simple and cheap appliances that charge continuously the battery, with a rythm of few amperes, for the time where the appliance is ON. If the holder do not close in time the charger, the battery will overcharge and her electrolytic faculty are lost with evaporation or likely exists destruction of her elements. The charger of circuit exceeds these faults. It checks electronic the situation of charge of battery and it has circuit of control with retroaction, that forces the battery charge with biggest rythm until charge completely. When charge completely, it turns on one RED led (LD2). The charger has been drawn in order to charge batteries of 12V, ONLY. What should watch it from what it manufactures the circuit, they are the cables that connect the transformer with the circuit and in the continuity the battery, should they are big cross-section, so that heat when it passes from in them the current of charge and also they do not cause fall of...

This circuit is a 5v to 12 DC-DC step-up converter circuit which is specially ideal for the usb powered applications. A usb has two current supply modes.Before deecting the connected device the maximum supplies is 100mA to the load.when recognizing device its increases the output current up to 500mA.the controller (LT1618) also provides two input currents modes 100mA and 500mA which is selected by the user. Output currents are limited due to the increased potential difference at the output. When the demand of the load increases, output voltage will start to decrease. For example, if the circuit operates in the 100 mA input mode, when the load is 35 mA, the output voltage will be kept at 12V. But if the load increases to 50 mA, output voltage will reduce to 8V to maintain the constant 100 mA input current.

Using ADP2300 ADP2301 step-down dc dc regulators with integrated power MOSFET, can be designed a very simple DC DC voltage converter. Output voltage delivered by these circuits can be adjusted from 0.8 volts, up to 0.85xVin , with ±2% accuracy. The maximum output current that can be provided by ADP2300 ADP2301 regulators is up to 1.2 A load current. 12V Step-Down Dc Converter Circuit Diagram   There are two frequency options: the ADP2300 runs at 700 kHz, and the ADP2301 runs at 1.4 MHz. These options allow users to make decisions based on the trade-off between efficiency and total solution size. Current-mode control provides fast and stable line and load transient performance.  Bellow you an see two design examples, which require few common electronic components.First circuit will provide a 2.5V output at a maximum current of 1.2A from an input voltage of 12 volts. Second circuit will provide a 5V output at a maximum current of 1.2A from an input voltage of 12 volts.

This is project of Simple 500W 12V to 220V Inverter Circuits Diagram. This is a Simple  500W 12V to 220V Inverter Circuits Diagram which produces an AC output at line frequency and voltage. 12VDC to 220V 50Hz inverter circuit will power 220V or 110V appliances from 12V car battery. The circuit is easy to make and is low cost. Use proper transformer.   The output (in watts) is up to you by selecting different power rating transformer and power transistor rating. If you load electronic device which require 120V AC, then use transformer with 120V in output.  500W 12V to 220V Inverter Circuits Diagram

12V to 220V Inverter Circuit Diagrams, Even though today’s electrical appliances are increasingly often self-powered, especially the portable ones you carry around when camping or holidaying in summer, you do still sometimes need a source of 230 V AC - and while we’re about it, why not at a frequency close to that of the mains? As long as the power required from such a source remains relatively low - here we’ve chosen 30 VA - it’s very easy to build an inverter with simple, cheap components that many electronics hobbyists may even already have 12V to 220V Inverter . 12V to 220V Inverter Circuit Diagrams Though it is possible to build a more powerful circuit, the complexity caused by the very heavy currents to be handled on the low-voltage side leads to circuits that would be out of place in this summer issue. Let’s not forget, for example, that just to get a meager 1 amp at 230 VAC , the battery primary side would have to handle more than 20 ADC !. The circuit diagram of 12V to 2...

his is the Simple 12V To 24V DC-DC Converter Circuit Diagram. This simple DC-DC converter can provide up to 24V from a 12V source. It can be used to run radios, small lights, relays, horns and other 24V accessories from a 12V vehicle with a maximum draw of about 800mA.   Simple 12V To 24V DC-DC Converter Circuit Diagram It can be used to charge one 12V battery from another, or step up the voltage just enough to provide necessary overhead for a 12V linear regulator. Using one op-amp as a squarewave oscillator to ring an inductor and another op-amp in a feedback loop, it won't drift around under varying loads, providing a stable 24V source for many applications. With a wide adjustment in output this circuit has many uses. 

Using ADP2300 ADP2301 step-down dc dc regulators with integrated power MOSFET, can be designed a very simple DC DC voltage converter. Output voltage delivered by these circuits can be adjusted from 0.8 volts, up to 0.85xVin , with ±2% accuracy. The maximum output current that can be provided by ADP2300 ADP2301 regulators is up to 1.2 A load current. 12V Step-Down Dc Converter Circuit Diagram There are two frequency options: the ADP2300 runs at 700 kHz, and the ADP2301 runs at 1.4 MHz. These options allow users to make decisions based on the trade-off between efficiency and total solution size. Current-mode control provides fast and stable line and load transient performance.  Bellow you an see two design examples, which require few common electronic components.First circuit will provide a 2.5V output at a maximum current of 1.2A from an input voltage of 12 volts. Second circuit will provide a 5V output at a maximum current of 1.2A from an input voltage of 12 volts.