My Light Diagram

Today we are all going to learn chip DS18B20 temperature. I Characteristics: The specification of the sensor DS18B20 can mention briefly as follows: • Use a wireless interface should just have one leg out to the media. • It is possible to measure the temperature in the range of -55 -> +125 oC.Voi temperature range -10 ° C to + 85 ° C, the accuracy of ± 0.5 ° C.Co temperature warning function sweeping away the value given. • Voltage: 3 - 5.5 V, you can configure multiple encryption level from 9-12 bits The greater the number of bits precision hon.Thoi conversion time is 750ms maximum temperature for 12 bit encryption • Current consumption in sleep mode tiny. • Each sensor has a unique identification code stored in memory 64-bit on-chip ROM (on chip), binary values ​​are laser engraved. • If configured for DS18B20 under 9,10,11,12 bit precision, we have respectively: 0.5 ° C, 12:25 ° C, 0125 ° C, 0.0625 ° C.Theo default manufacturer if they It is not configured mode, it will automatic...

Simple Wire-Break Alarm With Delay  Alarm and Security Here is a simple circuit of wire-break alarm that activates after a delay of 15 to 30 seconds. When the thin-wire loop running across the entrance door is broken, the alarm sounds after a delay of 15 to 30 seconds, the time period set through VR1. Thus the occupants get sufficient time to lock the room from the outside and catch the thief.   The circuit uses CD4060, which is a 14-stage ripple-carry binary counter/divider and oscillator. It is wired as a timer here and does not need input pulse for trigger. CD4060 gets activated as soon as the power supply is switched on. Output O13 of CD4060 goes high after the lapse of preset delay set through VR1. Transistor SL100 (T2) is wired as a switch to power the timer section built around CD4060. When the wire loop is closed, transistor T2 does not conduct. So power to the timer circuit is not available and the piezo buzzer does not sound.  Wire-Break Alarm With Delay ...

Portable loads such as video cameras, halogen flood lights, electrical irons, hand drillers, grinders, and cutters are powered by connecting long 2- or 3-core cables to the mains plug. Due to prolonged usage, the power cord wires are subjected to mechanical strain and stress, which can lead to internal snapping of wires at any point. In such a case most people go for replacing the core/cable, as finding the exact location of a broken wire is difficult. In 3-core cables, it appears almost impossible to detect a broken wire and the point of break without physically disturbing all the three wires that are concealed in a PVC jacket. The circuit presented here can easily and quickly detect a broken/faulty wire and its breakage point in 1-core, 2-core, and 3-core cables without physically disturbing wires. It is built using hex inverter CMOS CD4069. Gates N3 and N4 are used as a pulse generator that oscillates at around 1000 Hz in audio range. The frequency is determined by timing components...

This simple circuit lets you scan a 220V live wire. The clock input of the IC is connected to a wire, which acts as the sensor. Here, we have used 10cm length of 22SWG wire as the sensor. When you hold the sensor (metallic conductor or copper wire) close to the live wire, electric field from mains activates the circuit. As the input impedance of the CMOS IC is high, the electric field induced in the sensor is sufficient to clock it. The output obtained at pin 11 of CD4017 drives the LED. Flashing of the LED (LED2) indicates the presence of mains, while LED1 indicates that the scanner is active. 220V Live Wire Scanner Circuit Diagram The circuit can be used to find stray leakage from electrical appliances like fans, mixers, refrigerators, etc. It can be easily assembled on any general-purpose board or the discrete components can be directly soldered on the IC. A 9V PP3 battery powers the circuit. If you use a mains adaptor, make sure that it is well regulated and isolated; otherwise, ev...