My Light Diagram

This 5.1 surround amplifier circuit schematic use the IC AN7168 as the main component from this circuit . Minimum voltage required 12V and maximum voltage 24V , I recomended it 12 V because the voltage support on are components. But if you want to better a loud sound you can raise it.  Maximum power output 40W with impedance 4 ohm . This 5.1 surround amplifier circuit schematic also support to make surround sound or 5.1 speaker. Use this amplifier on rear speaker , left right , and center but dont use to subwoofer speaker. See 5.1 surround amplifier circuit schematic below : Click to view large If you want to make a 5.1 surround sound you must make 5 the circuit of 5.1 surround amplifier circuit schematic , for left and right speaker , rear left and right speaker , and center speaker. Use the subwoofer speaker with support amlplifier subwoofer circuit .

If you are looking for a low drop voltage regulator that can provide a power supply of 1A with an output voltage of between 5V and 20V DC, National Semiconductor LM2941 Low Dropout Adjustable Regulator is that you can pick to make use of. It's a typical dropout voltage of 0.5V which means that the input supply need only must be 0.5V DC over the desired output voltage. Its other features include internal short circuit current limit and reverse battery protection. As shown in the schematic below, the regulator has five pins which consists of the ON/OFF control, Input Voltage, Output Voltage, Ground & Adjustable pins. ON/OFF is used for the purpose of switching on & off of the regulator. The capacitors C1 & E1 are to be placed as close as feasible to the regulator. The output of the circuit can be varied by varying the worth of potentiometer VR1 from 5V DC to 20V DC. The input voltage is limited from five.5V DC to 30V DC. Resistor R1 must be greater than 1K. The worth of t...

5.1 channel amplifier consists of 6 amplifiers 1 channel mono, which has certain specifications on each canals. Has 6 channel surround sound amplifier that consists of Front Left ,Center,Front Right ,Rear Left (Left Surround),Rear Right (Right Surround) , and LFE ( Subwoofer ).For clarity I give a simple illustration of the layout and the circuit for these speakers . 5.1 Speaker Setup Accoustic Field Generator Acoustic Field Generator is generating acoustic sound with surround effects are adjustable with a standard Dolby Surround, able to produce surround sound is good enough but not too much need of funds. Technological developments as if not only focused on one area alone but on all fronts. The development of technologies that exist today one of them is in the field of audio. With more advanced audio technology today not only as mere entertainment but has become a hobby, hobby is not cheap of course. Many audio enthusiasts trying to make music sound that sounded to be ...

This solid-state push-pull single-ended Class A circuit is capable of providing a sound comparable to those valve amplifiers, delivering more output power (6.9W measured across a 8 Ohm loudspeaker cabinet load), less THD, higher input sensitivity and better linearity. Voltage and current required for this circuit are 24V and 700mA respectively, compared to 250V HT rail and 1A @ 6.3V filament heating for valve-operated amplifiers. The only penalty for the transistor operated circuit is the necessity of using a rather large Heatsink for Q2 and Q3 (compared to the maximum power delivered).In any case, the amount of heat generated by this circuit can be comparable to that of a one-valve amplifier. An optional bass-boost facility can be added, by means of R5 and C5.   Circuit diagram: Parts: P1 = 47K R1 = 100K R2 = 12K R3 = 47K R4 = 8.2K R5 = 1.5K R6 = 2.7K R7 = 100R R8 = 100R R9 = 560R-1/2W R10 = 1R-1/2W Q1 = BC560 Q2 = BD439 Q3 = BD439 C1 = 10uF-63V C2 = 10uF-63V C3 = 47uF-25V C4 = 10...

General Description: The BA5415A and BA5416 are dual power amplifier ICs that operate off a 9V to 15V supply. When driving a 4Ω load off a 9V supply, the BA5415A does not require a heatsink. The BA5416 uses a lost-cost package. The basic characteristics (total harmonic distortion etc.) of the amplifiers are excellent, and both ICs include a standby switch function. Features High output. POUT = 5.4W (VCC = 12V, RL = 3Ω and THD = 10%) POUT = 2.5W (VCC = 9V, RL = 4Ω and THD = 10%) Excellent audio quality. THD = 0.1% (f = 1kHz, PO = 0.5W) VNO = 0.3mVrms (Rg = 10kΩ) RR = 60dB (fRR = 100Hz) Wide operating power supply voltage range. VCC = 5.0V to 18.0V (BA5416 : 5.0V to 15.0V) Switching noise (ìpopî noise) generated when the power is switched on and off is small. Ripple mixing when motor starts has been prevented. Built-in thermal shutout. Built-in standby switch. Output is not influenced by the standby pin voltage. Mute time does not depend on VCC. Soft clipping. Heatsink not required  ...

Image CadSoft Eagle Professional 6.5.0 Multilingual | 44.27 MB EAGLE (Easily Applicable Graphical Layout Editor) is an ECAD program produced by Cadsoft in Germany. It is very commonly used by private electronics enthusiasts, because there is a very usable free demo version for nonprofit use and is available in English and German. Cadsoft has released versions for Microsoft Windows, Linux, and Mac OS X. EAGLE provides a schematic editor, for designing circuit diagrams and a tightly integrated PCB layout editor, which automatically starts off with all of the components required by the schematic. Components are manually arranged on the board, with the help of coloured lines showing the eventual connections between pins that are required by the schematic, to aid in finding a placement that will allow the most efficient track layout. It also provides a good autorouter, which once the components have been placed will attempt to automatically find an optimal track layout to make the electrica...

The STK402-900 series products are audio power amplifier hybrid ICs that consist of optimally-designed discrete component power amplifier circuits that have been miniaturized using SANYO's unique insulated metal substrate technology (IMST). The adoption of a newlydeveloped low thermal resistance substrate allows this product to integrate five power amplifier channels in a single compact package. 30 Watt x 5 Channels Audio Power Amplifier

Nokia may offer entry-level Windows Phone 7.5 devices by year's end, according to DigiTimes. Citing the usual "industry sources," DigiTimes said the new phones would be aimed at consumers in emerging markets, who are considered more price-sensitive. The hardware requirements for Windows Phone 8 are stricter than those for its predecessor, demanding a dual-core processor and support for near-field communication (NFC). Those features would be difficult to add to more entry-level and mid-level phones, according to the sources, prompting the need for less pricey Windows Phone 7.5 devices. (Credit: Josh Miller/CNET ) 

An increasing number of appliances draw a very small current from the power supply. If you need to design a mains-powered device, you could generally choose between a linear and a switch-mode power supply. However, what if the appliance’s total power consumption is very small? Transformer-based power supplies are bulky, while the switchers are generally made to provide greater current output, with a significant increase in complexity, problems involving PCB layout and, inherently, reduced reliability. Is it possible to create a simple, minimum part-count mains (230 VAC primary) power supply, without transformers or coils, capable of delivering about 100mA at, say, 5 V? A general approach could be to employ a highly inefficient stabilizer that would rectify AC and, utilizing a zener diode to provide a 5.1 V output, dissipate all the excess from 5.1 V to (230×√2) volts in a resistor. Even if the load would require only about 10mA, the loss would be approximately 3 watts, so a significant...

Sources have told BGR the iPhone 5 will indeed be a complete redesign, with an appearance much like the form factor of the iPad 2. The front glass of the next generation iPhone will be connected to an all-aluminum back via a rubberized bezel. The mockup below illustrates what the aluminum iPhone might look like. The bezel is said to be made of a similar material to the Apple Bumper cases. Not only would this bezel conceal a completely redesigned antenna system, it sounds like this would help make the iPhone 5 less slippery to hold. After all, the machined aluminum found on the iPad 2 is slick in more ways than one. BGR is confident the next iPhone will not see the light of day until next fall, which puts the release date approximately one year after the iPhone 4S launch. The days of a summer iPhone release seem to have fallen to the wayside for the time being. When it comes to the cellular antenna, using the rubberized bezel would permit Apple to configure the antenna without needing ...