My Light Diagram

Components List: R1 = 2K2 Ohm 2,5 Watt R2 = 240 Ohm R3,R4 = 0.1 Ohm 10 Watt R7 = 6K8 Ohm R8 = 10K Ohm R9 = 47 Ohm 0.5 Watt R10 = 8K2 Ohm C1, C7, C9 = 47nF C2 = 4700uF/50v – 6800uF/50v C3, C5 = 10uF/50v C4, C6 = 100nF C8 = 330uF/50v C10 = 1uF/16v C11 = 22nF D1…D4 = four MR750 (MR7510) diodes (MR750 = 6 Ampere diode) or 2 x 4 1N5401 (1N5408) diodes. D5 = 1N4148, 1N4448, 1N4151 D6 = 1N4001 D10 = 1N5401 D11 = LED D7, D8, D9 = 1N4001 TR = 2 x 15 volt (30volt total) 6+- Ampere IC1 = LM317 T1, T2 = 2N3055 P1 = 5k P2 = 47 Ohm or 220 Ohm 1 Watt P3 = 10k trimmer F1 = 1 Amp F2 = 10 amp Circuit Description: This is an easy to make power supply that has reliable, clear and regulator 0 to 28 Volt 6/8 Amp output voltage. By making use of two 2N3055 transistor, you’ll get two times the amount of electric current. Although the 7815 power regulator may kick in on short circuit, overload and thermal overheating, the fuses in the main section of the transformer and the fuse F2 at the output will safe yo...

                                    This is variable DC power supply circuit, or we can call it adjustable DC power supply which give us a 1.2V-25V output voltage. The power supply schematic above is taken from the datasheet of regulator LM338K manufactured National Semiconductor. The circuit uses IC LM338K as the voltage regulator, so we will get the stable and regulated output. The regulator IC LM338K provides 5A output current max, and the voltage from 1.2 to 32V, it also featured the integrated thermal and short-circuit protection. Maximum voltage at input and output of the regulator is 35V . The transformer current value depends your needs. For example, if you need 120W power output then you’ll need 5A transformer. 5A x 24V (full power) will give you 120W output power. Since this power supply circuit described to give us 1.2-25V DC output, then you must have transformer with 24V AC output. Fo...

VARIABLE PWM SPEED CONTROL

Here is a very Simple Electronic Circuit of 12-Bit Dac with Variable Step Size Circuit. The step size of the converter is variable by selection of the high order data bits. The first DAC, A, has a stable reference current supplied via the 10.24 V reference IC and Rl. R2 provides bias cancellation. As shown, only the first 4 MSB inputs are used, giving a step size of 225/256 2.048/16 = 0.127 mA. This current supplies the reference for DAC whose step size is then 0.1275/256 = 0.498 µ. Complementary voltage outputs are available for unipolar output and using R3 - R4 = 10, Vout is ± 10.2 V approximately, with a step size (1 LSB) of approximately 5 mV. If desired an op amp can be added to the output to provide a low impedance output with bipolar output symmetrical about ground, if R5 = R6 within 0.05%. 12-Bit Dac with Variable Step Size Circuit Diagram: Note that offset null is required, and all resistors except R2 and R3 should be 1% high stability types. By using lower order address lin...

If you are looking for a low drop voltage regulator that can provide a power supply of 1A with an output voltage of between 5V and 20V DC, National Semiconductor LM2941 Low Dropout Adjustable Regulator is that you can pick to make use of. It's a typical dropout voltage of 0.5V which means that the input supply need only must be 0.5V DC over the desired output voltage. Its other features include internal short circuit current limit and reverse battery protection. As shown in the schematic below, the regulator has five pins which consists of the ON/OFF control, Input Voltage, Output Voltage, Ground & Adjustable pins. ON/OFF is used for the purpose of switching on & off of the regulator. The capacitors C1 & E1 are to be placed as close as feasible to the regulator. The output of the circuit can be varied by varying the worth of potentiometer VR1 from 5V DC to 20V DC. The input voltage is limited from five.5V DC to 30V DC. Resistor R1 must be greater than 1K. The worth of t...

This 30v variable power supply circuit is based on LM317   voltage regulator circuit . This LM317 30v variable power supply circuit can deliver high current (around 5 amps) and variable output voltage between 1.2 volts, up to 30 volts. The led D3 mounted on pin 6 at lm301 lights in constant current mode . Circuit diagram  Current limit can be adjusted using R2 potentiometer and the output voltage can be adjusted from 1.2 volts to 30 volts using R8 potentiometer . Input voltage for this variable power supply must be around 35 volts .For this power supply circuit you need to use LM317K circuit (in to3 package ) which must be mounted on a heatsink .

Variable gain above is a circuit that is used to increase signal strength in dB , needed in a circuit of gains if the range is less reinforcement amplifier input signal, and the required input signal must be high enough so that the circuit is less then the maximum amplifier sound output. For the use of gain can be placed and connected directly to the input amplifier. Part List : R1___15K R2___4K7 R3___15K R4___4K7 R5___180R R6___2K RV1__10K Trim U1___NE5532

How to Build 1.2-30V/1.5A Variable Regulated Power supply, This is simple 1.2-30V/1.5A variable regulated power supply circuit diagram The 110V-AC coming from the powercord is fed to the transformer TR1 via the on-off switch and the 500mA fuse. The 30vac output (approximately) from the transformer is presented to the BR1, the bridge-rectifier, and here rectified from AC (Alternating Current) to DC (Direct Current). If you don't want to spend the money for a Bridge Rectifier, you can easily use four general purpose 1N4004 diodes. The pulsating DC output is filtered via the 2200µF capacitor (to make it more manageable for the regulator) and fed to 'IN'-put of the adjustable LM317 regulator (IC1). The output of this regulator is your adjustable voltage of 1.2 to 30volts varied via the 'Adj' pin and the 5K potmeter P1. The large value of C1 makes for a good, low ripple output voltage.  1.2-30V/1.5A Variable Regulated Power supply Circuit Diagram Why exactly 1.2V and not...

Power supply circuit to generate output below were variations between 1.3V DC to 12.2V DC with 1A current. In addition, the power supply circuit is also equipped with over-current protection or shield against belebih flow. Power supply circuit is very simple, but the quality is quite good, made her basiskan regulator IC LM723 is a pretty legendary. Description: R2 to set the output voltage. The maximum current is determined by R3, over-current protection circuit inside the LM723 to detect the voltage on R3, if it reaches 0.65 V, the voltage output will be off her. So the current through R3 can not exceed 0.65 / R3 although output short-circuit in his. C3 and C4 are ceramic capacitors, as much as possible directly soldered to the PCB, this is because the LM723 is prone to oscillation that is not cool. LM723 works with 9.5V input voltage to 40 V DC and the LM723 can generate its own current of 150mA when the output voltage is not more than 6-7V under input voltage. Specifications: Output...