My Light Diagram

Here , I will give a circuit of schemes that are used to combine 2 pieces input or stereo to 1 input mono. Why 2 inputs in to one because, if we need a stereo amplifier we want to become a stronger by combining the two input into one input, so that a higher power output. Actually without any circuit above we can combine stereo amplifier into mono, but the sound output less than the maximum , need for this additional combiner circuit. Part List = R1______150K R2______920R R3______150K R4______920R R5______920R U1______NE5532 For balance _: R1 / R2=R3 / R4 For balance _: R1 = R3 Gain ______: R5 / R1 = R5 / R3

This is low voltage high-current ouput , switching dc power supplly wiht input 220 Volts AC , In this circuit , an St2 diac relaxation oscilator, Q3 , C1 , and the diac , initiates conduction of the output switching transistor Q1, the on time of which is maintained constant by a separate timing / commutation network consisting of Q2 , C2 ,SUS , and SCR 1. See schmeatic diagram below : The output voltage , consequently , is independent on the duty cycle . To compensate for unwanted variations of output voltage because of input voltage or load resistance fluctuations , an H11C wired as a liniear - model unilateral pnp transistor in a stable different amplifier configuration is connected into the galvanically isolated negative- feedback loop.

The circuit charger is equipped with voltage output settings , so that we can regulate how much voltage to charge the battery. And the settings using the potentio making it easier for us managing voltage up to a mV. See charger circuit below : Adjust the circuit by setting the 500 Ohm resistor while it is attached to a fully charged battery. You can use the circuit to charge : Cells battery Wet Accu Dry Accu Nicad battery Solar battery

This amplifier circuit uses the output transformer as an additional amplifier in the output. You can use the transformer output transformer-old has not used but still in good condition, you can use it in this series. For this amplifier IC used is M51503L, this ic has a voltage limit of up to 7 volts only and a minimum of the incoming voltage about 2 volts. Actual output issued from the IC is 0.2 Watts, but once applied to the circuit maximum output of about 5.3 Watts. Part List : Resistor R1 = 75R R2 = 330R Capacitor C1 = 1uF C2 = 47uF C3 = 100uF C4 = 0.33uF C5 = 0.47uF Transformer T1 = Transformer Output OT240 IC IC1 = M51503L

Amplifier circuit is very suitable for use in subwoofer amplifier system based on IC SI1030G. Amplfier has 30W output with 8 ohm impedance. Supply voltage required minimum of 12 volts and a maximum of up to 22 volts DC. Component List : R1 = 100K R2 = 1R C1 = 2.2uF C2 = 100uF C3 = 47uF C4 = 100nF C5 = 10uF C6 = 47uF C7 = 100uF IC = SI1020GL , SI1030G

By using the circuit you do not bother to roll  up a transformer that is used to reduce voltage AC 220V to 7V ,9 V or 12V, etc. When using a large transformer we will find it hard to make transformator. by rolling hundreds or even thousands of times roll. But if you use this circuit a little just enough to roll trafo not to small, and its be relatively small. Part List : R1________________________________680K R2________________________________47K R3________________________________100R R4________________________________1K R5________________________________1R D1,D2,D3,D4,D7,D8,D9,D10__________1N4007 D5,D6_____________________________1N4148 C1________________________________2u2F 400V C2________________________________2n2 C3________________________________47uF 25V C4________________________________10n C5________________________________470uF / 16V Q1________________________________MJE13003 Q2________________________________S8050 This is construction of transformer. For the first toll 22...