Gibson Deluxe Tuners part three the fix


Please note that this post is part three of four posts. I highly recommend reading all four posts in order before acting on any of the information.

The other parts are located here:

Part 1: http://diystrat.blogspot.com/2009/01/gibson-deluxe-tuners-and-why-they-suck.html
Part 2: http://diystrat.blogspot.com/2009/01/gibson-deluxe-tuners-part-two.html
Part 4: http://diystrat.blogspot.com/2010/01/gibson-deluxe-tuners-revisit.html

OK! Done!

I tried various different options and finally settled on one that I was very happy with. Ironically, it was the one I thought wouldn’t work – the solder fix.

I had already tried the glue repair in the past, but it eventually broke again, so I didn’t even bother trying this time. However, it was going to be my last-resort fix if necessary.

Before I show you the solder fix, I should mention that I did try the metal strap solution first. I cut out a little paper template to fit over the tuner and then went hunting for a suitable piece of metal.

(paper template)



I really wanted to find a nice little piece of brass, but I found a piece of scrap sprung steel that was just the right size, so I thought I’d try that.

(piece of metal before I bent it to shape)



However, when I tried to bend it to a 90-degree angle, it snapped. I tried again with a different piece of metal, but the same thing happened. It’s still a possible solution, but you would need to find metal that wasn’t so prone to snapping, or know how to properly heat-treat it.

So I ditched the metal strap idea and tried solder instead. I was pleasantly surprised to see that it stuck to the tuner casing EXTREMELY well. So well, in fact, that the test blob I tried on the inside first was a pain to file off.

I assembled the tuner and held the back cover in a vice, then heated the join with a soldering iron, as shown here.



Now here it is with some solder added.



The whole tuner (and vice) acts as a heat sink, so you need to have a powerful enough soldering iron to heat up the area around the join before all the heat gets sucked away (be careful that you don’t accidentally lean the soldering iron against the tuner button, by the way - I nearly did that a couple of times). I used a 40 watt soldering iron, but I’d recommend you use at least 60 watts, if not substantially more. I’d also recommend that you don’t touch the tuner button with your finger (or anything else) until the metal has cooled down again, just in case it has softened up at all. And since I’ve already mentioned waiting, just wait until the whole tuner has cooled down before you touch it. Mine got VERY hot. And don’t blow on the tuner to cool it down quicker either - this is bad for solder joints.

Finally, a clean up with a file and we're done!



The tuner is now back on the guitar and the fix is completely hidden. A very satisfactory result indeed.

EDIT: I've since found out that there is another (known) trick to repairing these tuners, which is to attach the back cover, turn the tuner over and hit the middle of each tab with a punch. This distorts the tab just enough to give it some grip. More information here: http://diystrat.blogspot.com/2010/01/gibson-deluxe-tuners-revisit.html.

Comments

Post a Comment

Popular posts from this blog

Simple Active crossover Circuit Diagram with TL074

Image
This is a Simple Active crossover Circuit Diagram with TL074. An audio source, like a mixer, preamp, EQ, or a recorder, is fed to the input of the Electronic Crossover Circuit. This signal is either AC or coupling, depending on the setting of switch 51, the non-inverting input of buffer amplifier Ul-a, a section of a quad BIFET, low amp TL074 noise made by Texas Instruments op. This stage has a gain of 2, and its output is distributed to both a low pass filter made by R4, R5, C2, C3, and Uld op-amp, and a high-pass filter made by R6, R7, C4, C5, and op amp ULC.  These are12 dB / octave Butterworth filters. The response of the Butterworth filter was chosen because it gives the best compromise between the damping and phase. The values of capacitors and resistors varies depending on the selected connection that your device works. The filter outputs are fed to a balancing network made by R8, R9, RIO, R14 and potentiometer RLL balance. When the potentiometer is at its center position, t...
Keep reading

Build a Curve Tracer Circuit Diagram

Image
How to Build a Curve Tracer Circuit Diagram ? This is the simple Curve Tracer Circuit Diagram. This circuit Useful for checking diodes, transistors, triacs, SCRs, resistors, and LEDs, this curve tracer should prove useful in the experimenter`s lab.   Curve Tracer Circuit Diagram It displays the volt-ampere characteristic of a two-ter-minal device on an oscilloscope. This is a simple block diagram of the EZ-Curve. Current-limited AC signals are passed through both the device under test and a precision resistor to yield current and voltage readings.
Keep reading

Making an RIAA phono preamp

Image
Before we start today's blog post, I think I really need to clarify what we’re discussing. I’ve recently got back into vinyl in a big way. Part of the reason for this is the fantastic “Vinyl Decision” in Taipei, run by a couple of very fine gentlemen by the names of Mark and Terry ( https://www.facebook.com/VinylDecision / http://www.vinyldecision.com/ ). If you're in Taipei, and like music, pay them a visit. A recent purchase from there brought back memories of trying again, and again (and again) to play guitar like my guitar heroes as a teenager in the 1980s. In fact, vinyl is making quite a comeback worldwide. A lot of people are realizing that digital versions just lack some of the personality that vinyl can provide. Many of them are buying old record players/turntables and wiring them up to their modern amps. However, they are often disappointed to find that the output audio is very quiet and lacking bass. This is because records are/were recorded using a very specific f...
Keep reading