Sony HCD ZUX9 circuit diagram MINI Hi Fi COMPONENT SYSTEM US Model E Model Australian Model


ICs Used: STK412-150C – IS81LV6416-10TLT[S-RAM] – TMP92CD28AFG[USB controller] – M30624MGP-B33FPU0(US) or M30624MGP-B34FPU0(Except US)[System control] – M61537FP-RF0G(Rec-Playback AMP) – BH2210FV-E2 
Click on the pictures to zoom in
AUDIO POWER SPECIFICATION
(US model only)
POWER OUTPUT AND TOTAL HARMONIC DISTORTION:
With 6-ohm loads, both channels driven, from 120 Hz – 10 kHz; rates 160 watts per channel minimum RMS power, with no more than 10 % total harmonic distortion from 250 milliwatts to rated output.
Amplifier section
The following are measured at US model:
AC 120 V, 60 Hz
Other models:
AC 120, 220, 240 V, 50/60 Hz
Front/Surround speaker Power Output (rated): 160 W + 160 W (at 6 Ω, 1 kHz, 1% THD)
RMS output power (reference): 250 W + 250 W (per channel at 6 Ω, 1 kHz, 10% THD)
USB board schematic
Transformer board schematic
Main board schematic
Power amplifier board schematic


Comments

Post a Comment

Popular posts from this blog

Making an RIAA phono preamp

Image
Before we start today's blog post, I think I really need to clarify what we’re discussing. I’ve recently got back into vinyl in a big way. Part of the reason for this is the fantastic “Vinyl Decision” in Taipei, run by a couple of very fine gentlemen by the names of Mark and Terry ( https://www.facebook.com/VinylDecision / http://www.vinyldecision.com/ ). If you're in Taipei, and like music, pay them a visit. A recent purchase from there brought back memories of trying again, and again (and again) to play guitar like my guitar heroes as a teenager in the 1980s. In fact, vinyl is making quite a comeback worldwide. A lot of people are realizing that digital versions just lack some of the personality that vinyl can provide. Many of them are buying old record players/turntables and wiring them up to their modern amps. However, they are often disappointed to find that the output audio is very quiet and lacking bass. This is because records are/were recorded using a very specific f...
Keep reading

Build a Curve Tracer Circuit Diagram

Image
How to Build a Curve Tracer Circuit Diagram ? This is the simple Curve Tracer Circuit Diagram. This circuit Useful for checking diodes, transistors, triacs, SCRs, resistors, and LEDs, this curve tracer should prove useful in the experimenter`s lab.   Curve Tracer Circuit Diagram It displays the volt-ampere characteristic of a two-ter-minal device on an oscilloscope. This is a simple block diagram of the EZ-Curve. Current-limited AC signals are passed through both the device under test and a precision resistor to yield current and voltage readings.
Keep reading

Simple Active crossover Circuit Diagram with TL074

Image
This is a Simple Active crossover Circuit Diagram with TL074. An audio source, like a mixer, preamp, EQ, or a recorder, is fed to the input of the Electronic Crossover Circuit. This signal is either AC or coupling, depending on the setting of switch 51, the non-inverting input of buffer amplifier Ul-a, a section of a quad BIFET, low amp TL074 noise made by Texas Instruments op. This stage has a gain of 2, and its output is distributed to both a low pass filter made by R4, R5, C2, C3, and Uld op-amp, and a high-pass filter made by R6, R7, C4, C5, and op amp ULC.  These are12 dB / octave Butterworth filters. The response of the Butterworth filter was chosen because it gives the best compromise between the damping and phase. The values of capacitors and resistors varies depending on the selected connection that your device works. The filter outputs are fed to a balancing network made by R8, R9, RIO, R14 and potentiometer RLL balance. When the potentiometer is at its center position, t...
Keep reading